Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC Manuale Utente Pagina 99
- Pagina / 168
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
DeviceNet Adapter Parameters
B-7
Sets the Logic Command data that is sent to the drive if the
following is true:
• Comm Flt Action (10) is set to Send Flt Cfg and communications
are disrupted.
• Idle Flt Action (11) is set to Send Flt Cfg and the scanner is put
into Program or Test mode.
• Peer Flt Action (34) is set to Fault Cfg and communications are
disrupted.
The bit definitions will depend on the product to which the adapter is
connected.
Sets the Reference data that is sent to the drive if any of the
following is true:
• Comm Flt Action (10) is set to Send Flt Cfg and communications
are disrupted.
• Idle Flt Action (11) is set to Send Flt Cfg and the scanner is put
into Program mode.
• Peer Flt Action (34) is set to Fault Cfg and the scanner is put into
Program mode.
• Peer Flt Action (34) is set to Fault Cfg and communications are
disrupted.
Important: If the drive uses a 16-bit Reference, the most significant
word of this value must be set to zero (0) or a fault will
occur.
15 Flt Cfg Logic
Range:
0000 0000 0000 0000 to 1111 1111 1111 1111
Default:
0000 0000 0000 0000
Type:
Read/Write
Reset Required:
No
16 Flt Cfg Ref
Range:
0 to 4294967295
Default:
0
Type:
Read/Write
Reset Required:
No
- DeviceNet Adapter 1
- DPI AC Drives 1
- Contents 3
- List of Figures 7
- List of Tables 9
- Introduction 11
- 1.2 Related Documentation 12
- Electric 13
- Getting Started 15
- 2.2 Required Equipment 16
- 2.3 Installation Checklist 17
- Step Action Refer to 18
- Installing the 19
- 3.5 Applying Power 23
- Configuring the 25
- SP600 Standard 31
- 4.5 Setting the Data Rate 32
- Peer-to-Peer 33
- 4.9 Setting a Fault Action 41
- 4.10 Resetting the Adapter 43
- 00010xxx 45
- 01234567 45
- 1=Enabled 45
- 0=Disabled 45
- Configuring the Scanner 47
- AC Drive 48
- Edit I/O 49
- Parameters 49
- 5.4) appears 49
- 5.3.1 Mapping the Input I/O 52
- 5.3.2 Mapping the Output I/O 53
- 5.4 Saving the Configuration 54
- Using I/O Messaging 55
- 6.4 Using Reference/Feedback 58
- 6.5 Using Datalinks 58
- Using Explicit 67
- Messaging 67
- ControlLogix Controller 68
- Using Explicit Messaging 69
- PLC or SLC Controller 70
- Word Description 71
- 7.4 Running Explicit Messages 73
- 7.5 ControlLogix Example 74
- 7.6 PLC-5 Example 76
- Ladder Logic Program 77
- 7.7 SLC Example 78
- Troubleshooting the 81
- and Network 81
- 8.1.1 DRIVE Status Indicator 82
- 8.1.2 MS Status Indicator 83
- 8.1.3 NET A Status Indicator 84
- 8.2 Adapter Diagnostic Items 85
- Technical 91
- Specifications 91
- 1DPI Port 94
- 2 DPI Data Rate 94
- 3 DN Addr Cfg 94
- 4 DN Addr Actual 94
- 5 DN Rate Cfg 95
- 6 DN Rate Actual 95
- 7 Ref/Fdbk Size 95
- 8 Datalink Size 95
- 9 Reset Module 96
- 10 Comm Flt Action 96
- 11 Idle Flt Action 97
- 12 DN Active Cfg 97
- 13 DPI I/O Config 98
- 14 DPI I/O Active 98
- 15 Flt Cfg Logic 99
- 16 Flt Cfg Ref 99
- Figure B.3 – M-S Input (25) 100
- 26 M-S Output 101
- 27 COS Status Mask 101
- 28 COS Fdbk Change 101
- 29 COS/Cyc Interval 102
- Peer A Input 102
- Peer B Input 102
- 32 Peer Cmd Mask 103
- 33 Peer Ref Adjust 103
- 34 Peer Flt Action 104
- 35 Peer Node to Inp 104
- 36 Peer Inp Timeout 105
- 37 Peer Inp Enable 105
- 38 Peer Inp Status 105
- 43 Peer Out Skip 107
- DeviceNet 109
- C.1 Identity Object 110
- Services 111
- C.2 Connection Object 112
- C.3 Register Object 114
- Instance Attributes 115
- C.4 Parameter Object 116
- C.5 Parameter Group Object 119
- C.6 PCCC Object 121
- C.7 DPI Device Object 123
- C.8 DPI Parameter Object 127
- DeviceNet Objects 129
- Descriptor Attributes 130
- Decimal Places 131
- Decimal Place) 131
- C.9 DPI Fault Object 137
- C.10 DPI Alarm Object 140
- C.11 DPI Time Object 142
- Logic Command/ 145
- Status Words 145
- Logic Status Word 146
- Logic Command/Status Words 147
- Master-Slave 149
- I/O Configuration 149
- Datalinks 152
- Datalinks (Continued) 153
- Datalinks (Continued) 155
- Datalinks 156
- Glossary-1 157
- Glossary-2 158
- Glossary-3 159
- Glossary-4 160
- Glossary-5 161
- Glossary-6 162
Prodotti e manuali riguardandi Apparecchiature Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC
Apparecchiature Rockwell-automation RECOMM-485 RS485 DFI Communications Module Manuale Utente
(68 pagine)
(68 pagine)
Apparecchiature Rockwell-automation FactoryTalk Historian SE 3.0 H2H Interface Install Manuale Utente
(32 pagine)
(32 pagine)
Apparecchiature Rockwell-automation 20D PowerFlex 700S/700H Frame 10...14 Drives Maint Manuale Utente
(10 pagine)
(10 pagine)
Apparecchiature Rockwell-automation T8292 Trusted Power Distribution Unit MCB 24V Manuale Utente
(2 pagine)
(2 pagine)
Apparecchiature Rockwell-automation 1440-SPD02-01RB XM-220 Dual Speed Module Manuale Utente
(12 pagine)
(12 pagine)
Apparecchiature Rockwell-automation MD60 Door-Mount NEMA 1 OIM Bezel Kit MDI Manuale Utente
(6 pagine)
(6 pagine)
Apparecchiature Rockwell-automation Logix5000 Control Systems: Connect POINT I/O Modul Manuale Utente
(62 pagine)
(62 pagine)
Apparecchiature Rockwell-automation 1203-USB USB Converter (Same as DRIVES-UM001) Out Manuale Utente
(76 pagine)
(76 pagine)
Apparecchiature Rockwell-automation SP200 AC Drive, 1 2 Channel Analog, Preset Speed Manuale Utente
(68 pagine)
(68 pagine)
Apparecchiature Rockwell-automation 440N Magnetically Operated Safety Switch Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Rockwell-automation T8017 Trusted Peer to Peer Communications Manuale Utente
(46 pagine)
(46 pagine)
Apparecchiature Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui Manuale Utente
(112 pagine)
(112 pagine)
Apparecchiature Rockwell-automation FlexPak/WebPak 3000 DC Drive AutoMax Network Commu Manuale Utente
(108 pagine)
(108 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.116 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale