Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui Manuale Utente Pagina 81
- Pagina / 112
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
A-12
GV3000/SE Operator Interface Module (OIM) User Guide, Version 2.0
*Only supported for GV3000/SE Regulator board versions 6.0 and later.
TORQUE REG INT
GAIN
Torque Regulator
Integral Gain
Input U.015 Performance Tuning
(Vector) ⇒ Torque Loop
Tuning
TORQUE REG PROP
GAIN
Torque Regulator
Proportional Gain
Input U.014 Performance Tuning
(Vector) ⇒ Torque Loop
Tuning
TORQUE SELF-TUNE
EN
Torque Self-Tune Enable Input U.008 Quick Start (Vector)
Performance Tuning
(Vector) ⇒ Self Tuning
Parameters
TORQUE SELF-TUNE
RSLT
Torque Self-Tune Result Read only U.009 Performance Tuning
(Vector) ⇒ Self Tuning
Parameters
TRIM GAIN PERCENT Trim Gain Percentage Input P.015 Speed Control ⇒ Draw
& Trim Configure
TRIM REF SOURCE Trim Reference Source Input P.014 Speed Control ⇒ Draw
& Trim Configure
TS ANALOG IN
CONFIG
Terminal Strip Analog
Input Configure
Input P.011 Regulator Terminal Strip
TS ANALOG IN GAIN Terminal Strip Analog
Input Gain
Input P.010 Regulator Terminal Strip
TS ANALOG IN
OFFSET
Terminal Strip Analog
Input Offset
Input P.009 Regulator Terminal Strip
TS ANALOG OUT
SOURCE
Terminal Strip Analog
Output Source
Input P.012 Regulator Terminal Strip
TS DIG INPUT CONFIG Terminal Strip Digital
Inputs Configure
Input P.007 Regulator Terminal Strip
TS SPEED REF SEL Terminal Strip Speed
Reference Source
Input P.008 Regulator Terminal Strip
VHZ-CURVE TYPE Volts/Hertz Curve Type Input H.018 Application Setup
(V/Hz)
ZERO SPEED HOLD
TIME*
Zero Speed Hold Time Input U.025 Application Setup
(Vector)
Table A.1 – OIM Parameters Cross-Referenced to Software I/M Parameters and Parameter Numbers (Continued)
OIM Parameter Name
Software I/M
Parameter Name Type
Parameter
Number OIM Menu Path
- User Guide 1
- Version 2.0 1
- Contents 3
- List of Figures 5
- List of Tables 7
- 1.2 Related Publications 10
- Introduction to the OIM 11
- Display, and Indicators 13
- 2.2 The Display 17
- 2.2.2 Key Indicators 18
- Installing, Powering 21
- 3.2 Powering Up the OIM 24
- Using the OIM 31
- Figure 4.1 – Main Menu Screen 32
- Using Quick Start to 41
- Program the Drive 41
- Regulation 44
- REGULATION TYPE (P.048) 48
- ENCODER PPR (U.001) 49
- MOTOR POLES (U.002) 49
- MOTOR NAMEPL RPM (U.005) 50
- MOTOR NAMEPL HP (U.022) 50
- ACCEL TIME (P.001) 51
- DECEL TIME (P.002) 52
- MINIMUM SPEED (P.003) 52
- MAXIMUM SPEED (P.004) 53
- CURRENT LIMIT (P.005) 53
- MAGNET CURRENT PRCNT (U.006) 54
- Using the OIM to Monitor and 55
- Control the Drive 55
- 6.3.1 Starting the Drive 59
- 6.3.2 Stopping the Drive 59
- Troubleshooting the Drive 60
- 7.2.1 Reviewing the Fault Log 62
- Figure 7.6 – Alarm Menu 64
- Figure 7.8 – Diagnostics Menu 65
- 7.6 OIM Failures 67
- Panel Keypad/Display Codes 68
- Software I/M Parameters and 70
- Parameter Numbers 70
- Input r.010 Option Port 76
- Input r.015 Option Port 78
- GV3000/SE OIM Menu and 88
- Parameter Organization 88
- Installed) 93
- • RMI Inputs 93
- • RMI Outputs 93
- B.1.10 Memory Functions 94
- B.1.11 Additional Parameters 94
- B.2.10 Memory Functions 100
- B.2.11 Additional Parameters 100
Prodotti e manuali riguardandi Apparecchiature Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui
Apparecchiature Rockwell-automation FlexPak/WebPak 3000 DC Drive AutoMax Network Commu Manuale Utente
(108 pagine)
(108 pagine)
Apparecchiature Rockwell-automation 20D PowerFlex 700S/700H Frames 10...14 IP00, NEMA/ Manuale Utente
(64 pagine)
(64 pagine)
Apparecchiature Rockwell-automation Sipha 6 Coded Magnetic Interlock Sensor Actuator Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Rockwell-automation 1769-L30ER_L30ERM_L30ER-NSE_L33ERM_L33ER_L36ERM Co Manuale Utente
(88 pagine)
(88 pagine)
Apparecchiature Rockwell-automation T8449 Trusted TMR 24Vdc Valve Monitor Module Manuale Utente
(2 pagine)
(2 pagine)
Apparecchiature Rockwell-automation FactoryTalk AssetCentre Machine Edition Installati Manuale Utente
(44 pagine)
(44 pagine)
Apparecchiature Rockwell-automation 284D On-Machine ArmorStart Accelerator Toolkit Manuale Utente
(188 pagine)
(188 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale