Rockwell-automation 193-EC4 EC4 Current Monitoring Relay User Manual Manuale Utente Pagina 42
- Pagina / 157
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Rockwell Automation Publication 193-UM011A-EN-P - September 2010 43
Protective Trip and Warning Functions Chapter 3
Parameter 46, UL Trip Delay, allows the installer to define the time period that an
underload condition must be present before a trip occurs. It is adjustable from
0.1…25.0 seconds.
Parameter 47, UL Trip Level, allows the installer to define the current at which
the EC4 Current Monitoring Relay will trip on an Underload.
Communication Fault
Protection
A disruption of the communication link between the EC4 Current Monitoring
Relay and a DeviceNet network can result in the loss of application control
and/or critical process diagnostic data. Rapid communication fault detection
helps minimize potential damage due to uncontrolled or unmonitored
applications.
Comm Fault Trip
The EC4 Current Monitoring Relay will trip with a Comm Fault indication if:
• No trip currently exists
• Comm Fault protection is enabled
• The EC4 Current Monitoring Relay experiences a loss of communication
If the relay trips on a Comm Fault, the following will occur:
• The Network Status LED will blink red or become solid red
• The TRIP/WARN LED will flash a red 10-blink pattern
• Bit 9 in Parameter 14, Trip Status, will go to “1”
• Bit 0 in Parameter 21, Device Status, will go to “1”
• The Trip Relay contacts will open
• The outputs will be placed in their Protection Fault State (if so
programmed)
IMPORTANT
The underload inhibit timer starts after the maximum phase of load
current transitions from 0 A to 30% of the device’s minimum FLA Setting.
The EC4 Current Monitoring Relay does not begin monitoring for an
underload condition until the UL Inhibit Time expires.
IMPORTANT
For any given application, the practical limit of ULTrip Level (Parameter
47) will be dependent on the FLA setting and the lower limit of the EC4
Current Monitoring Relay’s current measurement capability. See Table 20
- on page 83.
IMPORTANT
The Protection Fault State of OUT A and OUT B is defined by Parameter
65 (OUTA Pr FltState), Parameter 66 (OUTA Pr FltValue), Parameter 71
(OUTB Pr FltState), and Parameter 72 (OUTB Pr FltValue).
- EC4 Current Monitoring Relay 1
- Important User Information 2
- IMPORTANT 3
- DNET-UM072_-EN-P 4
- Table of Contents 5
- Product Overview 10
- Diagnostic Parameters 12
- Trip Relay 12
- Inputs and Outputs 12
- Status Indication 13
- Test/Reset Button 13
- Node Address Switches 14
- DeviceNet Compatibility 14
- Flash Memory 14
- Installation and Wiring 15
- Starter Installation 16
- Starter Assembly Instructions 17
- 193-EC_ _E) 18
- Cat. No. 193-EC_ _B) 20
- Cat. No. 193-EC_ _E) 21
- Power Terminals 22
- Terminal Designations 23
- Grounding 24
- Short-Circuit Ratings 24
- Fuse Coordination 25
- Typical Motor Connections 25
- Single-Phase Full-Voltage 26
- External Line Current 27
- Transformer Application 27
- Installation Instructions 28
- External Ground Fault 29
- Sensor Application 29
- E3 Plus Overload Relay 30
- Cat. No. 193-CBCT_ 30
- Ground Fault Sensor 30
- Cat. No. 193-CBCT1 31
- Typical Control Circuit 32
- Wiring Diagrams 32
- Single-Phase 33
- Three-Phase 33
- Warning Enable 35
- Overcurrent Protection 35
- Introduction 35
- Trip Enable 35
- Overcurrent Warning 36
- Overcurrent Trip 36
- Ground Fault Protection 37
- Ground Fault Setting Range 38
- Ground Fault Trip 38
- Ground Fault Trip Inhibit 39
- Ground Fault Warning 39
- Undercurrent Protection 40
- Undercurrent Trip 41
- Communication Fault 42
- Protection 42
- Communication Idle 43
- Comm Idle Warning 44
- Remote Trip 44
- Preventive Maintenance 45
- Diagnostics 45
- Queue Clearing 46
- DeviceNet Node Commissioning 47
- Using RSNetWorx for DeviceNet 48
- Figure 26 - EDS Wizard Screen 50
- Programmable Parameters 57
- Monitor Params (All 58
- Read-Only) 58
- Advanced Setup Group 60
- For Catalog Number 193-EC4ZZ 66
- Reset/Lock Group 71
- DeviceNet Setup Group 72
- Output Setup Group 75
- DeviceLogix Group 79
- Current Monitoring Parameters 81
- Reporting Accuracy 82
- Ground Fault Current 83
- Reporting 83
- Monitor Group 83
- Trip History and Snapshot 90
- Trip History Codes 92
- Warning History Codes 93
- Trip Snapshot 94
- Explicit Messaging 96
- (0x0375) 102
- Using DeviceLogix™ 104
- DeviceLogix Programming 105
- Troubleshooting 110
- Network Status LED 111
- OUT A & OUT B LEDs 111
- DeviceNet Modes of 112
- Operation 112
- Power-Up Sequence 112
- Run Mode 113
- Recoverable Error Mode 113
- Unrecoverable Error Mode 113
- Resetting a Trip 114
- Trip/Warn LED 114
- Procedures 114
- DeviceNet Troubleshooting 115
- Input and Output 115
- ➊ FRN 2.000 and later 116
- Specifications 117
- Table 4 - Input Ratings 118
- Environmental 119
- Table 9 - Protection 120
- DeviceNet Information 122
- Identity Object – Class 123
- Code 0x01 123
- Message Router – Class 124
- Code 0x02 124
- DeviceNet Object – Class 124
- Code 0x03 124
- Assembly Object – Class 125
- Code 0x04 125
- Input Assemblies 126
- Connection Object – Class 128
- Code 0x05 128
- Discrete Input Point Object 132
- – Class Code 0x08 132
- Discrete Output Point 132
- Object – Class Code 0x09 132
- Parameter Object – Class 133
- Code 0x0F 133
- Parameter Group Object – 135
- Class Code 0x10 135
- Control Supervisor Object – 139
- Class Code 0x29 139
- Acknowledge Handler 142
- Object – 0x2B 142
- DeviceNet Interface Object 143
- – Class Code 0xB4 143
- ODVA Fault Codes 144
- Logic Supervisor Object 145
- CLASS CODE 0x030E 145
- Status Object - CLASS 145
- CODE 0x0375 145
- CE Compliance 148
- Low Voltage Directive 149
- Two-Speed Applications 150
- Accessories 151
- Rockwell Automation Support 157
- Documentation Feedback 157
Prodotti e manuali riguardandi Apparecchiature Rockwell-automation 193-EC4 EC4 Current Monitoring Relay User Manual
Apparecchiature Rockwell-automation 150-CF147 SMC-3 (43-85A)/SMC-Delta (74-147A) Soft Manuale Utente
(1 pagine)
(1 pagine)
Apparecchiature Rockwell-automation 140G-H-xxxx Stored Energy Operating Mechanism Manuale Utente
(5 pagine)
(5 pagine)
(6 pagine)
Apparecchiature Rockwell-automation 599-GR4_GR5 Service Disconnect Ground Kit for Bul Manuale Utente
(1 pagine)
(1 pagine)
Apparecchiature Rockwell-automation 440R MSR45E Safety Relay Expansion Module User Man Manuale Utente
(12 pagine)
(12 pagine)
Apparecchiature Rockwell-automation 140 Manual Motor Starter / Circuit Breaker Manuale Utente
(7 pagine)
(7 pagine)
Apparecchiature Rockwell-automation 141A Mounting Ssystem MCS Star Tutorial Manuale Utente
(40 pagine)
(40 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale