Rockwell-automation 1771-DB Basic Module User Manual - Series A Manuale Utente Pagina 21
- Pagina / 167
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Installing the BASIC Module
Chapter 3
3–7
If the FLT LED lights after the module has been operating properly check
the following troubleshooting chart.
Problem Probable Cause Recommended Action
Module’s programming port
does not respond
Hardware failure Send module for repair
Module’s programming port
continues to function but FLT
LED goes on and off
Problem with block-transfers
between processor and BASIC
module
Verify ladder logic
Module’s programming port
continues to function and FLT
LED goes out when processor
is switched to program mode
Module’s programming port
continues to function and FLT
LED remains on
Problem with block-transfer
circuitry on the BASIC Module
Send module for repair
The BASIC Module has a 32 K byte EPROM installed (figure 3.4). We
recommend that you keep JEDEC standard 8 K, 16 K or 32 K byte
EPROMs which use 12.5V DC programming voltage as spares. You can
buy 32 K byte EPROMs from Allen-Bradley (part numbers 940654-02 or
9406454-03).
3.3
Module Status LED’s
(continued)
3.4
Installing the User Prom
- 1771–DB Basic 1
- Allen-Bradley 1
- Table of Contents 2
- Table of Contents iii 4
- Table of Contentsiv 5
- Table of Contents v 6
- Table of Contents vii 8
- Using This Manual 9
- Important information 10
- Conventions 10
- Introducing the BASIC Module 11
- General Features (continued) 12
- Hardware Features 12
- Software Features 13
- 2.5 Specifications 14
- Installing the BASIC Module 15
- Chapter 3 16
- Module Keying 17
- Configuration Plugs 17
- Module Installation 19
- Initial Start-up Procedure 19
- Module Status LED’s 20
- Installing the User Prom 21
- Electrostatic 23
- Discharge 23
- Battery (continued) 24
- Using the Serial Ports 25
- Chapter 4 26
- Program Port 27
- Connecting a T3/T4 Industrial 29
- Terminal to the Program Port 29
- Configuring the Software 31
- Peripheral Port 32
- Connecting A T30 Industrial 34
- Terminal (1784-T30) to the 34
- Peripheral Port (continued) 34
- Connecting 36
- RS-422 Devices 36
- Assembly Parts 37
- Argument 42
- Control Stack 42
- Description of Commands 43
- Command: RUN 43
- Command: CONT 44
- Command: LIST 44
- Command: LIST# or LIST 45
- Command: Disabling Control C 46
- Commands: RAM and ROM 48
- [integer] (continued) 48
- Command: XFER 49
- Command: PROG 49
- Command: PROG1 51
- Command: PROG2 51
- Statement: CLEARS 54
- Statements: CLOCK1 54
- READ – RESTORE 55
- Statements: DAT 55
- Statement: DIM 56
- Statements: DO – UNTIL 56
- [rel expr] 56
- [rel expr] (continued) 57
- Statements: DO – WHILE 58
- Statements: GOSUB [ln num] 61
- – RETURN (continued) 61
- Statement: GOTO [ln num] 61
- Statements: IF – THEN – 63
- ELSE (continued) 63
- Statement: INPUT 63
- Statement: LD@ [expr] 65
- Statement: LET 66
- Statement: ONERR 67
- [ln num) 67
- Statement: ONTIME 68
- [expr],[ln num] 68
- [expr], [ln num] (continued) 69
- Statement: PRINT or P 69
- Special Print Formatting 70
- Statements 70
- Statements (continued) 71
- Statement: PRINT# or P.# 73
- Statements: 74
- PH0., PH1. 74
- PH0.#, PH1.# 74
- Statement: PUSH[expr] 75
- Statement: POP[var] 76
- Statement: REM 77
- Statement: STOP 79
- Statement: STRING 79
- Dual Operand (dyadic) 81
- Operators (continued) 81
- Unary Operators 82
- Relational Expressions 86
- Special Operators 87
- Special Function Operators 87
- System Control Values 89
- Data Transfer Support 89
- Routines 89
- Enable Interrupts – CALL 9 92
- Input Call Conversion 92
- Output Call Conversion 94
- Routines (continued) 94
- Peripheral Port Support 96
- Peripheral Port Support – 96
- Parameter Set – CALL 30 96
- Get Numeric Input 100
- Character from Peripheral 100
- Port – CALL 35 100
- Port – CALL 35 (continued) 101
- Chapter 5 102
- Operating Functions 102
- The ASC Operator 109
- (continued) 110
- The CHR Operator 111
- String Support Calls 112
- 5.10.3.9 124
- Reset the Peripheral Port 132
- CALL 119 132
- Programming 133
- Chapter 6 134
- PLC-2 Processor Program 135
- PLC-3 Family Processors 137
- PLC-5 Family Processors 140
- Programming Tips 142
- Data Types 143
- 6-digit, Signed 146
- Fixed Decimal BCD 146
- 3.3-digit, Signed 147
- Input Data Types 148
- Editing A Procedure 149
- Editing 150
- Procedure 150
- Chapter 8 150
- Renumber (continued) 151
- Editing a Simple 152
- Procedure 152
- Error Messages and Anomalies 153
- Error Messages from 154
- BASIC (continued) 154
- Error Messages and 155
- Anomalies 155
- Chapter 9 155
- String Support CALL 157
- Error Messages 157
- Anomalies (continued) 160
- Quick Reference Guide 162
- Appendix 163
- Conversion Table 164
- BASIC Module 166
- Programming Hints 166
- Worldwide representation 167
Prodotti e manuali riguardandi Apparecchiature Rockwell-automation 1771-DB Basic Module User Manual - Series A
Apparecchiature Rockwell-automation 1734-ACNR POINT I/O ControlNet Adapter User Manual Manuale Utente
(110 pagine)
(110 pagine)
Apparecchiature Rockwell-automation 1747-DCM,D17476.8 Direct Communication Module Manuale Utente
(80 pagine)
(80 pagine)
Apparecchiature Rockwell-automation 1771-OBN DC (10-30V) Output Module Installation In Manuale Utente
(16 pagine)
(16 pagine)
Apparecchiature Rockwell-automation 1769-BOOLEAN Compact I/O BOOLEAN Module Installati Manuale Utente
(28 pagine)
(28 pagine)
Apparecchiature Rockwell-automation 1794-IV16_OV16_OV16P Flex I/O Digital DC Sourcing Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Rockwell-automation 1771-QDC, D17716.5.87(Passport) CLAMP AND EJECT MO Manuale Utente
(236 pagine)
(236 pagine)
Apparecchiature Rockwell-automation 1757-FFLDC4 ControlNet Foundation Fieldbus Linking Manuale Utente
(32 pagine)
(32 pagine)
Apparecchiature Rockwell-automation 1756-LSC8XIB8I ControlLogix Low-speed Counter Modu Manuale Utente
(84 pagine)
(84 pagine)
Apparecchiature Rockwell-automation 1784-KTCS ControlNET Scanner Installation Instruct Manuale Utente
(32 pagine)
(32 pagine)
Apparecchiature Rockwell-automation 1768-EWEB CompactLogix EtherNet/IP Web Server Modu Manuale Utente
(24 pagine)
(24 pagine)
Apparecchiature Rockwell-automation 1792D-16BVT0CD ArmorBlock MaXum 16 Input Module wi Manuale Utente
(16 pagine)
(16 pagine)
Apparecchiature Rockwell-automation 1769-OB16 Compact Solid State 24V dc Source Output Manuale Utente
(20 pagine)
(20 pagine)
Apparecchiature Rockwell-automation 1734-VHSC24 Point I/O Very High Speed Counter Modu Manuale Utente
(28 pagine)
(28 pagine)
Apparecchiature Rockwell-automation 1769-OF8V CompactLogix Analog Output Module Manuale Utente
(40 pagine)
(40 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale